Silverstone has finally launched the FLP03, a retro-inspired microATX chassis that pairs 1990s desktop aesthetics with modern hardware compatibility. Featuring a beige finish, the case has three 5.25″ expansion bays at the front and a functional Turbo button that triggers full-throttle cooling.

The FLP03's interior layout accommodates microATX and Mini-ITX motherboards, as well as graphics cards up to 413mm in length and PSUs up to 200mm in length. Builders can install liquid cooling radiators up to 360mm, tower coolers up to 169mm tall, a 180mm front fan, a 120mm rear fan, and various top fan configurations with 120mm and 140mm fans. Storage options include a mix of 5.25″, 3.5″, and 2.5″ drives across the three front bays and internal mounts.

SilverStone's exterior design is made to look like the type of PCs we had in the 1990s, including retro style buttons. A built-in front fan PWM display monitors system cooling, while a functional turbo button can let you ramp your fans up to max speeds.

Connectivity is handled by a front I/O panel containing USB-C, USB 3.0, audio, and microphone ports. The case is available with an MSRP of $179.99.

KitGuru says: Combining nostalgic 1990s styling with support for 360mm radiators and long graphics cards makes the FLP03 an interesting option for builders wanting a retro aesthetic without sacrificing performance.

The post SilverStone launches the retro-looking FLP03 mATX case with a functional Turbo button first appeared on KitGuru.

Montech has launched the TG3, a budget-friendly ATX fish-tank style case featuring a tiered bottom layout, back-connect motherboard support, and pre-installed unibody fans.

This new TG3 case comes in black or white finishes and is tailored for performance systems with a minimalist exterior design. It includes a spacious interior that offers clearance for GPUs up to 430mm long and compatibility with back-connect motherboards. Ambient ARGB lighting (28 LEDs) is also integrated directly into the PSU shroud to enhance the build's overall visual footprint.

Cooling out of the box relies on a pre-installed Montech GF360 U REV side intake and a GF120 U rear exhaust (140mm fans are also compatible). The side intake uses a unibody, single-frame design that should reduce resonance and simplify cable routing. Additionally, users can mount up to 3x 120/140mm fans on top and two 120mm fans on the PSU shroud. Radiator cooling is limited to 240mm on the side intake, but the top panel supports up to 280/360mm variants.

The front I/O is quite decent for such a cheap case, offering the typical power/reset buttons, 2x USB-A 3.0 ports, a USB-C port, and a headset audio jack. The Montech TG3 is now available for $59.

KitGuru says: Offering back-connect motherboard compatibility and unibody fans at such a low price point makes the TG3 a highly competitive option.

The post Montech releases affordable TG3 ATX case with back-connect motherboard support first appeared on KitGuru.

Cooler Master has announced the Q300L V3, the next generation of its compact microATX case, alongside a modular version called the Qube 340.

The updated Q300L chassis supports Mini-ITX and mATX motherboards within a small desktop footprint. It has room for graphics cards up to 366mm long, CPU coolers up to 178mm tall, and up to six cooling fans in total. Airflow potential is boosted by enlarged front-panel perforations and compatibility with a 140mm rear exhaust fan.

Structural improvements over the V2 include reinforced fan mounts, an upgraded motherboard tray, and a tempered glass side panel. For connectivity, the refreshed front I/O panel houses three USB 3.2 Gen 2×2 Type-C ports, dual USB 3.2 Gen 1 Type-A ports, and a combo audio jack.

Builders can opt for this standard layout, but the company is also offering the modular Qube 340 alternative. This version shares the same core mATX foundation but introduces optional handles, support for vertical or horizontal system orientations, and flexible front I/O placement. It additionally includes front-mounting support for compatible 3D-printable accessories.

KitGuru says: The original Q300L was a popular budget option, and adding modern USB-C connectivity alongside other improvements sweetens the deal. 

The post Cooler Master announces Q300L V3 and modular Qube 340 cases first appeared on KitGuru.

NZXT has announced the H6 series cases, featuring a dual-chamber design and support for back-connect motherboards. The new ATX chassis also features a one-piece curved tempered glass side panel for an unobstructed view of components.

With a 55-litre internal volume, the chassis supports ATX, mATX, and Mini-ITX motherboards. Two versions are available at launch in both black and white finishes. The standard H6 comes without pre-installed fans, while the H6 RGB+ includes two F360 RGB Reverse intake fans, an F120 RGB exhaust fan, and an NZXT Control Hub Lite. Front connectivity consists of two USB-A 3.2 Gen1 ports and one USB-C 3.2 Gen2x2 port.

Cooling configurations centre around 120mm fan compatibility, with space for up to ten fans across the angled side, top, bottom, and rear mounts. Users can fit up to a 360mm radiator in the top panel. Internal clearances accommodate graphics cards up to 390mm long, CPU air coolers up to 165mm tall, and PSUs up to 200mm in length. An integrated, adjustable GPU anti-sag bracket is included.

These cases are now available for $99.99 for the standard model and $199.99 for the RGB+ version.

KitGuru says: The dual-chamber design trend continues to evolve, and adding support for back-connect motherboards makes sense for a case focused heavily on clean aesthetics.

The post NZXT reveals new H6 mid-tower first appeared on KitGuru.

We take a quick look at the JOYJOM stackable PC test bench as an alternative to running motherboards bare on a desk for testing

The post Quick Look JOYJOM Stackable PC Test Bench Cheap But Cheap appeared first on ServeTheHome.

Formula V Line has announced it will preview the Air Power G10 mid-tower case at Computex 2026, featuring a uniquely designed front panel with three independent fans that can be tilted to direct airflow towards different components. 

The defining architectural feature of the Air Power G10 is its dynamic front ventilation layout. Rather than using standard fixed mounts, the three pre-installed 120mm front intake fans are mounted on independent, modular tilting brackets. This allows users to angle individual fans to direct airflow straight towards hotspots, such as the graphics card or CPU socket. Each fan bracket features a quick-release mechanism and includes a dust filter.

The structural foundation also includes an interchangeable bottom chamber module that can be adjusted forward or backward to restructure internal cable space and thermal zones. Up top, the chassis employs a tool-free, removable panel to assist with installing a top-mounted liquid-cooling radiator.

The mid-tower serves as the lead product for a massive 2026 lineup consisting of 22 new products, many of which will be on display at Computex 2026 next week.

Discuss on our Facebook page, HERE.

KitGuru says: Do you like the idea of having individually adjustable front fans?

The post Formula V Line unveils Air Power G10 with tilting front intake fans first appeared on KitGuru.

Today we’re looking at the new accessory ecosystem for the Corsair Frame 4000 case series. I reviewed the Frame 4000D about a year ago when Corsair first introduced its modular chassis design, now the company is expanding that idea with a range of upgrade parts and customisation options. New accessories include alternative front and side panels, replacement motherboard trays, a redesigned power supply shroud, plus an updated front I/O panel with improved USB connectivity. Corsair is clearly pushing the Frame platform as something you can maybe evolve rather than replace outright… but how useful are these upgrades, and are any of them worth buying? Let’s find out.

Timestamps:

00:00 Start
00:56 Accessories Overview
01:52 Alternative Motherboard Trays
03:33 Front Panel Options
08:18 Side Panel Options
13:43 Alternative Power Supply Shroud
14:27 Front I/O Panel (ELITE)
15:53 James' Thoughts

Frame 4000 Series Accessories: Corsair Frame Configurator

• Elite Front Panel I/O – $24.99 / £29.99
• Rapid Route 2.0 Motherboard tray – $9.99 / £10.82
• ELITE Motherboard Tray – Meteorite Aluminium – $79.99 / £69.99
• Full Tempered Glass Side Panel – $19.99 / £21.65
• Flat Steel Side Panel – $14.99 / £16.24
• LCD Mounting Kit – $39.99 / £29.99
• Cold Air Intake Kit – $39.99 / £29.99
• RGB FLOW Front Panel – $19.99 / £21.65
• WOOD Front Panel – $29.99 / £29.99
• ELITE WOOD Front Panel – $49.99 / £59.99
• Flat Glass Front Panel – $19.99 / £21.65
• Series Pixel Glass Front Panel – $19.99 / £21.65
• Compact PSU Shroud – $14.99 / £16.24

Front I/O:

• Elite Front Panel I/O: Comes with 3 x USB Type C Ports (1x USB 3.2 Gen 2×2 Type-C 20Gb/s port and 2x USB 3.2 Gen 1 Type-C 5Gb/s ports)  and a swappable MX-Style Green mechanical power button. The standard Front I/O comes with 1 x USB Type-C port and 2 x USB Type-A ports.

Motherboard Tray Options:

• RapidRoute 2.0 Motherboard Tray – A Pegboard motherboard tray designed to make cable management easy, allowing the user to move and rotate the ratcheting cable ties for customised cable management.
• ELITE Motherboard Tray – Meteorite Aluminium – Premium motherboard tray made from a single piece of aluminium, high rigidity and light weight with diamond cut edges – Supports E-ATX, ATX, Micro ATX, including reverse connector boards.

Front Panel options:

• RGB FLOW Front Panel – High air flow front panel with built-in RGB lighting -completely different look from the stock 3D-Y design.
• Flat Glass Front Panel – Solid glass for showing off front fans.
• Pixel Glass Front Panel – A full glass panel that allows unobstructed RGB lighting and creates a pixelated visual.
• Wood Front Panel – Made using real FSC certified wooden slats for a natural look, but still retaining great airflow  – available in black/walnut or white/oak.
• ELITE Wood Front Panel – again made from fsc certified wooden slats with a wavy parametric design and a central Corsair logo – also available in black/walnut or white/oak.

Side Panels Options:

• Full Glass Side Panel – ideal if you want to show off your whole system; you can even run it with the PSU shroud completely removed for a more retro look and to show off your power supply.
• Flat steel Side Panel – if you don’t want to see inside at all.
• Cold Air Intake Kit – 2/3 glass and a fan bracket for 3 x 120mm fans.
• LCD Mounting Kit – 2/3 glass and a slot to fit the Xenon Edge 14.5” LCD touchscreen – plus all cables for internal connectivity.

PSU Shroud:

• Compact PSU Shroud – ideal for pairing with the tempered glass front panels to show off your build. Mesh design with 2 x 120mm fan mounts on top. The standard 4000D/X case comes with a full-length power supply shroud.

Build Specification

• CPU – AMD Ryzen 7 9800X3D
• Motherboard – MSI X870 Tomahawk WiFi
• Graphics Card – Gigabyte RTX 5080 Gaming OC
• Memory – 32GB (2 x 16GB modules) Corsair Vengeance RGB DDR5-6000
• Storage – 1TB Corsair MP600 Elite PCIE Gen4 NVMe M.2 SSD
• CPU Cooler – Corsair Nautilus 360 RS ARGB
• Power Supply – Corsair RM1200X Shift ATX3.0 80+ Gold
• Case fans – Stock
• Chassis – Corsair Frame 4000D (Various Configurations)
• Operating System – Windows 11 24H2

KitGuru says: There's a decent range of accessories to fit most users' budgets, but if you want the full high-end, premium look with the Xenon Edge display its going to work out quite expensive. But if your taste of PC cases is all about aesthetics, it might be a price worth paying?

The post Corsair Frame 4000 Series Accessories Hands-On first appeared on KitGuru.

Gamdias has launched its new flagship PC case – the Atlas P6 CG. This one is for PC gamers who want their build to be the centrepiece of their set-up, with panoramic views of the internals, and even a dedicated platforms for displaying figurines. 

The Atlas P6 CG has a curved glass panel that wraps from the front to the right hand side, giving a multi-angle view of your internal components. A dedicated figure display platform with an omni‑directional spotlight allows users to present collectibles alongside hardware, while a tool‑free side‑panel clasp provides quick access for swapping components or display items.

As you may expect, this case also supports back-connect, connector-hidden (BTF) motherboards, so you can keep all of your motherboard power connectors in the rear-side of the case and reduce clutter in the front. There are plenty of Velcro tie points and 90mm of depth to keep everything tidy at the back as well.

Cooling is handled via a chimney-style ventilation design that draws cold air from the lower section and expels heat through the upper and rear panels. The case comes equipped with four pre-installed 120mm Notus M1 PWM ARGB fans arranged as three slanted bottom intakes directed toward the graphics card and one rear exhaust. An included 8-port PWM ARGB fan hub manages lighting and speed synchronisation, while dual integrated ARGB light strips provide additional illumination.

Motherboard compatibility includes ATX, microATX, and Mini-ITX motherboards. There's also space for graphics cards up to 425mm in length, CPU coolers up to 165mm in height, power supplies up to 200mm deep, and liquid cooling radiators up to 360mm on the top panel. The front I/O configuration includes a USB-C 3.2 Gen 2×2 port (20Gbps), two USB-A 3.0 ports, dedicated LED control, a spotlight toggle switch, and HD audio. Removable magnetic dust filters are fitted to the top, side, and bottom panels.

The Gamdias Atlas P6 CG has launched with an MSRP of $139.99.

Discuss on our Facebook page, HERE.

KitGuru says: Would you like to build a system inside one of these? 

The post Gamdias unveils new flagship Atlas P6 CG PC case first appeared on KitGuru.

Sama has introduced the S50, a compact ATX case that ships with four pre‑installed 120mm ARGB PWM fans, aiming to deliver strong airflow and lighting straight out of the box.

The S50 uses a front‑mounted PSU compartment to reduce overall footprint while maintaining hardware compatibility. It supports ATX, Micro‑ATX, Mini‑ITX, and back‑connect ATX/Micro‑ATX motherboards, along with graphics cards up to 410mm long, CPU coolers up to 165mm tall, and ATX power supplies up to 180mm long. For expanded cooling, the case accommodates up to 11 fans and a 360mm radiator at the top.

In the table below, you can see the full spec sheet for the case:

Model	S50
Dimensions	(L) 475 x (W) 235 x (H) 426mm
Color	Black / White
Material	SPCC: 0.7 / 0.8 / 0.9mm Tempered Glass: 4.0mm ABS
Motherboard Support	ATX / Micro-ATX / Mini-ITX
Back Connect Motherboard	ATX / Micro-ATX
Expansion Slot	7
Storage	4 x 2.5” SSD 3 x 3.5″ HDD
GPU Length Clearance	410mm (Max.)
CPU Cooler Height Clearance	165mm (Max.)
PSU	ATX (Max. 180mm)
Fan Support	Front: 3 x 120mm Top: 3 x 120mm Rear: 1 x 120mm Bottom: 3 x 120mm Side: 1 x 120mm
Radiator Support	Top: 360 / 240 / 120mm Rear: 120mm
Pre-Installed Fans	Front: 3 x 120mm ARGB PWM Fans Top: N/A Rear: 1 x 120mm ARGB PWM Fan Bottom: N/A Side: N/A
Pre-Installed Fan Specs	Speed: 700–1500 ±10% RPM Air Flow: 64.9 CFM Air Pressure: 1.65 mm-H₂O Noise: 26.8 dB(A)
I/O Ports	1 x Power Button 1 x LED Button 1 x HD Audio 2 x USB 3.0 1 x USB 3.2 Gen 2×2 Type‑C
Dust Filters	1 x Bottom 1 x Right side panel

Airflow is handled by the four included ARGB PWM fans, controlled through an integrated ARGB/PWM hub supporting up to six fans. Lighting can be managed via the front‑panel LED button or synced with motherboard software. As the case supports six fans in total, there is plenty of room for you to add extra cooling later on if needed.

To simplify building, the S50 features tool‑less quick‑release side, front and top panels. Behind the motherboard tray, you will find 47mm of cable‑management space, multiple tie‑down points and defined routing channels help keep wiring tidy. Storage is supported through a removable bracket that holds up to three 3.5‑inch HDDs or four 2.5‑inch SSDs.

The Sama S50 is available in the US now, in black or white colour options, priced at $110.

KitGuru Says: Do you often look for pre-installed fans when shopping for a new PC case?

The post Sama launches S50 PC case with back-connect support and ARGB fans first appeared on KitGuru.

Montech is celebrating its 10‑year anniversary with TEN, a new modular case built around a highly adaptable internal layout and support for multiple cooling and hardware configurations.

The Montech TEN has a reconfigurable structure that includes nine PSU mounting positions, three motherboard orientations and seven GPU installation options, giving builders plenty of freedom to adjust the chassis based on their cooling and space needs. The case supports air coolers up to 155mm and 360mm radiators on both the top and side panels, with a 9mm slim rear‑fan design improving internal clearance. Its airflow system is based on a chimney‑style layout, drawing cool air from the bottom and exhausting heat upward.

Montech offers three operating modes: M1 for air‑cooled builds, M2 for liquid‑cooling setups and I3 for compact SFF‑focused layouts. The exterior uses a precision metal mesh panel that acts as an optical filter, replacing traditional glass while diffusing internal lighting.

Each TEN case ships with a commemorative anniversary kit, marking Montech’s decade in the PC hardware market. In the UK, the Montech TEN is listed at £54.98 at SCAN, with some retailers offering limited‑time bundle promotions.

Discuss on our Facebook page, HERE.

KitGuru Says: We should get a closer look at this during Computex next month, so stay tuned for more.

The post Montech celebrates 10-year anniversary with new modular PC case first appeared on KitGuru.

Sharkoon has expanded its case lineup with the Steel Shark, a dual‑chamber ATX chassis built for clean layouts, strong airflow, and high‑end hardware. With tempered‑glass panels, four pre‑installed ARGB PWM fans, and support for BTF motherboards, it targets builders who want tidy cable management and a showcase‑ready system.

The dual‑chamber structure separates the main hardware area from the PSU and storage, keeping the primary chamber uncluttered while drives and cables sit behind the motherboard tray. The rear chamber includes mounts for two 2.5‑inch SSDs and a 3.5‑inch HDD, reinforcing the case’s focus on a clean presentation.

Cooling flexibility is a major focus. The Steel Shark supports up to eleven fans across the chassis: three 120mm or two 140mm in the front, three 120mm or two 140mm on the top, two 120mm on the side, two 120mm on the bottom, and a single 120mm at the rear. Radiator support includes simultaneous installation of two units, such as a 360mm top radiator paired with a 240mm or 280mm front unit. A five‑port ARGB controller and five‑port PWM hub come pre‑installed to simplify lighting and fan management.

Component clearance is generous, with room for GPUs up to 42.4cm long, CPU coolers up to 16.8cm tall, and power supplies up to 24.4cm. The case also supports BTF‑design ATX motherboards, further improving cable routing by shifting connectors to the rear.

KitGuru Says: At the very least, Steel Shark is a very cool name.

The post Sharkoon debuts Steel Shark dual-chamber PC case first appeared on KitGuru.

Today we’re taking a look at the Antec Flux Pro Noctua Edition, a full-tower case designed around high airflow and low-noise performance. It combines Antec’s Flux Pro chassis with a set of pre-installed Noctua G2 fans, tuned to deliver strong cooling with minimal acoustic impact. The case features extensive ventilation and support for large radiators, high-end GPUs, and oversized air coolers. In this review, we’ll be checking build quality, layout, and thermal performance to see how it stacks up.

Timestamps:

00:00 Start
00:44 Pricing / Costs
01:38 Accessories
02:02 Dimensions
02:14 Materials / Build
03:00 Recommended Fan Config
03:19 Front I/O (top)
03:47 Temperature display
04:27 Getting Inside the case / Colours
07:13 Install Options
12:27 Rotated PSU Design
13:36 Right hand side / drive positions
17:10 Floor of the case
17:55 Testing Methodology
19:08 Thermal and Noise Performance
21:09 Visual Airflow demo and thoughts
23:22 Closing Thoughts

Features:

• Pre-installed Noctua G2 fans – Includes four Noctua NF-A14x25 G2 and two NF-A12x25 G2 premium fans, delivering high-end airflow straight out of the box.
• Optimised for low noise operation – Noctua’s Extensive lab testing and offset fan speeds are designed to reduce vibration and “beat frequency” hum for quieter performance.
• Integrated fan hub and clean wiring – It also comes with a pre-wired NA-FH1 fan hub for synchronised control and simplified cable management.
• High-airflow Flux Pro chassis design – Flux Pro Noctua Edition is built on a low-airflow-resistance platform designed to maximise cooling efficiency for high-performance systems.

Specifications:

• Case Type: ATX Full Tower
• Dimensions (LxWxH): 530 x 245 x 546 mm
• Materials: Steel, Tempered Glass, Walnut Wood, Silicone, Plastic
• Motherboard Support: STX, Mini-ITX, µATX, ATX, E-ATX (Max 280mm)
• Back-connect motherboard support: No
• Expansion Slots: 8
• Storage bays: 5” x 2 / 2.5/3.5” x 4
• Max GPU Length: 455mm
• Max CPU Cooler Height: 190mm
• PSU Type: ATX up to 470mm (300mm with HDD) (180mm Rotated 90°)
• Cable Routing Space: 5mm
• Supplied Fans: 3x NF-A14x25 G2 PWM (Front), 2x NF-A12x25 G2 PWM (PSU shroud), 1x NF-A14x25 G2 PWM (rear)
• Fan Support: 3 x 120 / 3 x 140mm (Front), 3 x 120 /  3 x 140mm (Top), 2 x 120 / 2 x 140mm (Bottom), 1 x 120 / 1 x 140mm (Rear) 3 x 120mm (PSU Shroud)
• Radiator Support: 120/140/240/280/360/420 mm (Front/Top), 120/140mm (Rear/Bottom), 120/240/360mm (PSU Shroud)
• Dust Filters:
• Font I/O: 1x USB-C 3.1 (10 Gbit/s), 2x USB-A 3.0 (5 Gbit/s), 3.5 mm headphone/mic combo jack, Power / Reset / Temperature / Display Switch
• LCD Screen: Yes – Temperature Display

Thermal Performance Testing

To simulate thermal demand, we run the Cinebench R23 multi-thread benchmark and 3DMark Speed Way stress test simultaneously in a loop for 30 minutes to load the system fully. This gives the CPU and GPU enough time to reach constant steady-state temperature. With this data, we can compare how the system handles the thermal demand and measure peak noise levels.

Thermal performance is measured with the case in various configurations, such as the default, with the tempered glass left-hand side panel removed and with the front panel removed to see how these configurations affect the CPU and GPU temperature. During testing, only stock case fans are used unless otherwise specified. All water pumps are set to maximum RPM and fans are set to a custom RPM curve by the Motherboard software/BIOS.

All temperature measurements are presented as Deltas – meaning the ambient temperature has been deducted from the CPU temperature, giving us a Delta. Data shown in the charts represents the average component temperature over the length of the test as measured by HWiNFO, and then the last 15 minutes of the data are calculated to get the average. The ambient temperature during thermal tests is between 19-20⁰C.

Test System Specification:

• CPU – AMD Ryzen 7 9800X3D
• Motherboard – MSI MAG X870 Tomahawk WiFi
• Graphics Card – Gigabyte RTX 5080 Gaming OC
• Memory – 32GB (2 x 16GB Modules) G.SKILL Trident Z5 Neo RGB DDR5-6000
• Storage – 1TB Corsair MP600 Elite PCIE Gen4 NVMe M.2 SSD
• CPU Cooler – Noctua NH-D15 G2 LBC
• Power Supply – Seasonic Focus GX-1000 ATX 3
• Case fans – Stock (Noctua NF-A14x25 G2 PWM / NF-A12x25 G2 PWM)
• Chassis – Antec Flux Pro Noctua Edition
• Operating System – Windows 11 24H2

Thermal Performance Overview

We tested the case thermals using a Noctua NH-D15 G2 LBC / 360mm AIO as the exhaust at the top and with the case in several different fan configurations. The default configuration shown in the charts is with the Noctua NH-D15 G2 LBC CPU cooler, 3 x 140mm front intake fans, 2 x 120mm PSU shroud intake fans, 1 x 140mm rear exhaust fan and with all panels installed.

Thermal performance from the Flux Pro Noctua Edition is generally very strong. In the default configuration, CPU temperatures average 56°C over ambient, with the GPU at 45 °C. There is a clear improvement over the air-cooled setup when using a top-mounted 360mm AIO. This is due to the AIO's increased cooling power rather than any limitation of the case.

However, in the air-cooled setup, adding top fans as exhaust negatively affects CPU thermals, raising temperatures to 58°C, suggesting an airflow disruption. Adding a 120mm top intake fan can have a minor improvement in CPU temperature, but GPU temperature is unchanged with both top fan configurations, so leaving top fans out completely is fine.

GPU temperature remains consistent across most setups at around 45°C over ambient, highlighting the effectiveness of the case’s airflow design in the recommended configuration. Removing the PSU shroud fans leads to a small increase in GPU temperature at 48°C. Overall, the results show that the case performs best with balanced airflow in the default configuration, delivering solid all-around thermal performance.

Noise Output

Noise performance is fairly consistent across test configurations, with load noise at 46 dBA in the default setup, which doesn’t really change whether you switch to top intake or add extra exhaust fans. Noise shifts slightly when you remove the PSU shroud fans or install a top-mounted AIO, increasing to 48 dBA under load, suggesting those configurations introduce a bit of fan noise from the GPU cooler and from the AIO compared with the default configuration and using the D15 G2 air cooler.

Idle noise, however, is rock solid across the board at 36 dBA. Overall, it’s a pretty well-balanced acoustic in any configuration, but clearly best optimised in the recommended Noctua configuration.

Closing Thoughts

The Antec Flux Pro Noctua Edition is a case that does exactly what it sets out to do — deliver strong airflow, great cooling and low noise performance. In testing, it handles both CPU and GPU thermals with ease, and more importantly, it manages to keep noise levels impressively low, not just at idle, but also under load. Something that case manufacturers don’t always get right with pre-installed fan configurations. However, the Noctua Fans are not pre-installed; this is the job of the user. They arrive in a separate box.

A big part of that comes down to the included Noctua fans. You’re getting a set of high-quality NF-A12x25 and NF-A14x25 G2 units, along with a Noctua fan hub, all designed to work together. Build quality is exactly what you’d expect from an Antec/Noctua partnership, and the colour scheme is carried throughout the case, giving it a very distinct look that suits the whole package very well and will no doubt please Noctua enthusiasts.

In terms of compatibility, there’s plenty to like here too, including support for dual 420mm radiator installation, as well as generous clearance for large air coolers such as the Noctua NH-D15 G2 and high-end graphics cards. So whether you’re building a high-performance air-cooled system or going all-in with liquid cooling, the Flux Pro has the space and layout to handle it. But this means the case is quite large with Full tower dimensions, not ideally suited to placement on top of the desk.

That said, it’s not without its downsides. At around £350, it’s a very expensive case; at that price, you start to expect a bit more in terms of features. There’s no integrated GPU support bracket, no back-connect motherboard support, and some of the internal panels — particularly the top and front fan mounting brackets could be more intuitive to remove. Even so, if your main priority is excellent cooling performance with low noise levels straight out of the box, the Antec Flux Pro Noctua Edition is a very capable, premium option.

The Antec Flux Pro Noctua Edition is available to purchase now from Amazon priced at £348.90 HERE.

Pros: 

• Great thermal performance and low noise.
• Very high-quality fans included.
• Built-in fan hub.

Cons:

• Expensive.
• Missing basic key features such as an integrated GPU support arm, tool-free parts, and back-connect motherboard support.
• Fans are not pre-installed.

KitGuru says: If you have the cash to splash on a case and want a large chassis with great cooling and low noise, then this might be ideal, especially for Noctua enthusiasts. But in the current economic conditions, it could be money better spent on core system components.

The post Antec Flux Pro Noctua Edition PC Case Review first appeared on KitGuru.

Today we’re checking out the new 3200D case from Corsair. It’s a compact mid-tower chassis aiming to combine strong airflow with the latest builder-friendly features, including support for 360mm radiators, reverse-connection motherboards, and graphics cards up to 370mm long. In this RS ARGB version, you also get three included fans, a tempered glass side panel, and a built-in GPU support bracket. But how well does it actually perform? Let’s find out.

Timestamps:

00:00 Intro
00:48 Meet the 3200D – pricing and variants
01:19 Key specs
03:08 Accessing internals
05:34 Cooling and hardware support
07:51 At the back of the case
08:22 Behind the mobo tray
11:02 The case floor
11:48 Accessories and setup
12:24 Thermals and noise
13:34 James’ thoughts so far
14:45 Some compromises made…
16:19 USB 2.0?! And a potential explanation…
19:24 Last minor negative
19:55 Closing thoughts

Features:

• Strong Cooling Potential – Supports up to nine 120mm fans with three RS120 ARGB fans included out of the box and 360mm radiators are supported front and top.
• Reverse-Connector Motherboard Support – Compatible with reverse-connector motherboards, helping create clean builds with minimal visible cabling.
• GPU-Focused Design – Includes a built-in GPU anti-sag stabilisation arm and angled PSU-shroud fan mount to direct airflow toward the graphics card.

Specifications:

• Case Type: ATX Mid Tower
• Dimensions (LxWxH): 476 x 214 x 446mm
• Materials: Steel, Plastic, Tempered Glass
• Motherboard Support: ATX / mATX, Mini-ITX
• Back-connect motherboard support: Yes
• Expansion Slots: 7
• Storage bays: 2 x 2.5” / 1 x 3.5”
• Max GPU Length: 370mm
• Max CPU Cooler Height: 165mm
• PSU Type: ATX up to 180mm
• Pre-installed Fans: 3 x RS120 ARGB (Front)
• Fan Support: 3 x 120 / 2 x 140mm (Top), 3 x 120 / 2 x 140mm (Front), 2 x 120mm (Bottom), 1 x 120mm (Rear)
• Radiator Support: 360 / 280 / 240mm (Top), 360 / 280 / 240mm (Front)
• Dust Filters: Front / Bottom / Top
• Front I/O: 1 x USB 3.2 Gen 2 Type-C (20Gbps), 1 x USB 2.0 Type-A, 3.5mm Audio and Mic Combo Jack, Power Button
• LCD Screen: N/A

Thermal Performance Testing

To simulate thermal demand, we run the Cinebench R23 multi-thread benchmark and 3DMark Speed Way stress test simultaneously in a loop for 30 minutes to load the system fully. This gives the CPU and GPU enough time to reach constant steady-state temperature. With this data, we can compare how the system handles the thermal demand and measure peak noise levels.

Thermal performance is measured with the case in various configurations, such as the default, with the tempered glass left-hand side panel removed and with the front panel removed to see how these configurations affect the CPU and GPU temperature. During testing, only stock case fans are used unless otherwise specified. All water pumps are set to maximum RPM and fans are set to a custom RPM curve by the Motherboard software/BIOS.

All temperature measurements are presented as Deltas – meaning the ambient temperature has been deducted from the CPU temperature, giving us a Delta. Data shown in the charts represents the average component temperature over the length of the test as measured by HWiNFO, and then the last 15 minutes of the data are calculated to get the average. The ambient temperature during thermal tests is between 19-20⁰C.

Test System Specification:

• CPU – AMD Ryzen 7 9800X3D
• Motherboard – MSI MAG X870 Tomahawk WiFi
• Graphics Card – Gigabyte RTX 5080 Gaming OC
• Memory – 32GB (2 x 16GB Modules) G.SKILL Trident Z5 Neo RGB DDR5-6000
• Storage – 1TB Corsair MP600 Elite PCIE Gen4 NVMe M.2 SSD
• CPU Cooler – Corsair Nautilus 360 RS ARGB
• Power Supply – Seasonic Focus GX-1000 ATX 3
• Case fans – Stock (Corsair RS120 ARGB)
• Chassis – Corsair 3200D RS ARGB
• Operating System – Windows 11 24H2

Thermal Performance Overview

We tested the case thermals with a 360mm AIO as the exhaust at the top and in several different configurations. The default configuration shown in the charts is with the 360mm AIO at the top, 3 x 120mm RS ARGB fans at the front as intake and with all panels installed.

Looking at the thermal results, the 3200D performs consistently across all of our test configurations. With the case in its default setup, we saw CPU temperatures of 52°C and GPU temperatures of 47°C above ambient, which are solid out of the box results.

Removing the glass side panel or the dust filters doesn't make a meaningful difference, suggesting airflow through the chassis is already quite unrestricted by default. Interestingly, adding bottom fans shaves a few degrees off the GPU temperature, dropping it to 44°C, which shows that directing airflow toward the graphics card can provide a small benefit.

Noise Output

Moving on to noise output, results are again consistent across the different configurations. In the default setup the system measures 49 dBA under full load, while idle noise sits at a steady 36 dBA regardless of configuration.

Removing the dust filters or the glass side has little impact, with load noise varying only slightly from 49 to 50 dBA. The configuration with bottom fans installed produces the lowest load noise at 48 dBA, suggesting the additional airflow allows the GPU fans to work a little less aggressively under load, lowering overall system noise.

Closing Thoughts

Taken as a whole, the Corsair 3200D is a solid addition to the affordable airflow-focused case market. In our testing it delivers strong thermal performance with little variation in performance across configurations, so the case is well optimised for airflow and cooling straight out of the box. Build quality is also impressive for the price point, with a sturdy overall feel and a generally clean, understated design that should appeal to a wide range of consumers.

Hardware support is positive too, as the case manages to squeeze in high-end components despite its fairly compact mid-tower footprint. There’s room for large graphics cards, decent CPU cooler clearance, 360mm AIOs and support for several motherboard formats, which helps make the 3200D a flexible platform for mainstream gaming builds. While the interior layout does involve a few compromises due to the case dimensions, overall it still offers a fairly straightforward building experience.

That said, there are a few areas where the design feels slightly underdeveloped. The 360mm top radiator support is there technically, but compatibility can be limited depending on radiators and fan size, plus installation itself is a little awkward without a detachable top panel or radiator/fan bracket. Similarly, the front I/O feels somewhat dated with the inclusion of a USB 2.0 Type-A port, where a USB 3.0 connection would make more sense for a modern chassis. This could come down to the choice of reverse connector motherboard support and tight right-hand side clearance for cable management, although Corsair suggests otherwise.

There are also some smaller usability quirks to be aware of. The included GPU support bracket may not work with some graphics cards, particularly those with fans that extend lower than the shroud, plus there's no fan/ARGB hub included. However, these drawbacks don’t completely undermine what the Corsair 3200D does well. With strong airflow performance, solid build quality and good overall hardware support, it remains a capable budget builder-friendly case – even if a few design tweaks could have made it a much stronger contender.

The Corsair 3200D RS ARGB is has an MSRP of £79.99 here in the UK.

Pros:

• Strong airflow and cooling,
• Solid build quality at this price point.
• Good hardware support for its size, even with the compromises with a top 360 rad.

Cons:

• Top 360 radiator compatibility is limited, and installation can be awkward.
• USB 2.0 Type-A should be upgraded to USB 3.0.
• No detachable top rad/fan mount.
• GPU support bracket not compatible/interferes with fans on some graphics cards.
• No fan/ARGB hub included.

KitGuru says: Corsair almost nailed it with the 3200D, it has great cooling potential and hardware support, but some extra attention to detail would have resulted in a more well-rounded case.

The post Corsair 3200D RS ARGB Case Review first appeared on KitGuru.

Today we’re taking a look at the Cougar CFV235 mid-tower chassis. It features Cougar’s Central Floating Ventilation design, support for up to EATX motherboards, including back connect, and comes with pre-installed ARGB PWM fans straight out of the box. On paper, there’s plenty of cooling potential too with support for up to nine fans and 360mm radiators, along with clearance for graphics cards up to 430mm long. As always, we’ll be checking out build quality, ease of installation, thermal performance, and overall value to see if the CFV235 is worth considering for your next build.

Timestamps:

00:00 Intro
00:45 Pricing + key info
02:38 Getting inside
04:10 Cooling support, pre-installed fans
05:55 CPU and GPU compatibility
06:52 Looking at the rear
07:18 Area behind the mobo tray
09:32 Storage support
10:21 Floor of the case
11:17 Accessories
12:14 Thermal tests + noise
13:49 James’ experience so far
15:19 Closing thoughts

Features:

• Central Floating Ventilation (CFV) structure: A unique floating chamber design that creates separation between the PSU cabin and main chamber to enhance airflow and gives the case its distinctive look.
• Pre-installed Unity 240 ARGB PWM reverse-blade fan & Aurora RGB lighting: Included is a Cougar Unity 240 single-frame ARGB fan and an integrated Aurora RGB lighting strip for enhanced cooling and aesthetics.
• Versatile hardware support: CFV235 is compatible with motherboards up to E-ATX size, including back connect, 360mm radiators, 175mm tall air coolers and supports GPUs up to 430 mm in length.

Specifications:

• Case Type: Mid Tower
• Dimensions (LxWxH): 235 × 493 × 460 mm
• Materials: Steel, Plastic, Glass
• Motherboard Support: Mini ITX / Micro ATX / ATX / CEB
• Back-connect motherboard support: Yes
• Expansion Slots: 7
• Storage bays: 5″ ×2, 2.5″ ×2 + 2 (converted from 3.5″ bays)
• Max GPU Length: 430mm
• Max CPU Cooler Height: 175mm
• PSU Type: ATX up to 200mm
• Pre-installed Fans: Unity 240 ARGB PWM Reversed Fan × 1 (Side) 120mm ARGB PWM Fan × 1 (Rear)
• Fan Support: 120mm × 3 / 140mm × 3 (Top), 120mm ×2 (Side), 120mm x 3 (Bottom), 120mm x 1 (Rear)
• Radiator Support: 360mm / 280mm / 240mm / 140mm / 120mm (Top), 120mm (Rear)
• Dust Filters: Bottom
• Front I/O: USB 3.2 Gen 2×2 Type-C ×1, USB 3.0 Type-A ×2, 4-Pole Headset Audio Jack ×1, RGB Button
• LCD Screen: N/A

Thermal Performance Testing

To simulate thermal demand, we run the Cinebench R23 multi-thread benchmark and 3DMark Speed Way stress test simultaneously in a loop for 30 minutes to load the system fully. This gives the CPU and GPU enough time to reach constant steady-state temperature. With this data, we can compare how the system handles the thermal demand and measure peak noise levels.

Thermal performance is measured with the case in various configurations, such as the default, with the tempered glass left-hand side panel removed and with the front panel removed to see how these configurations affect the CPU and GPU temperature. During testing, only stock case fans are used unless otherwise specified. All water pumps are set to maximum RPM and fans are set to a custom RPM curve by the Motherboard software/BIOS.

All temperature measurements are presented as Deltas – meaning the ambient temperature has been deducted from the CPU temperature, giving us a Delta. Data shown in the charts represents the average component temperature over the length of the test as measured by HWiNFO, and then the last 15 minutes of the data are calculated to get the average. The ambient temperature during thermal tests is between 19-20⁰C.

Test System Specification:

• CPU – AMD Ryzen 7 9800X3D
• Motherboard – MSI MAG X870 Tomahawk WiFi
• Graphics Card – Gigabyte RTX 5080 Gaming OC
• Memory – 32GB (2 x 16GB Modules) G.SKILL Trident Z5 Neo RGB DDR5-6000
• Storage – 1TB Corsair MP600 Elite PCIE Gen4 NVMe M.2 SSD
• CPU Cooler – Montech HyperFlow Digital 360
• Power Supply – Seasonic Focus GX-1000 ATX 3
• Case fans – Stock
• Chassis – Cougar CFV235
• Operating System – Windows 11 24H2

Thermal Performance Overview

We tested the case thermals with a 360mm AIO as the exhaust at the top and in several different configurations. The default configuration shown in the charts is with the 360mm AIO at the top, Cougar Unity 240 intake side fan, 1 x 120mm rear exhaust and with all panels installed.

In our thermal testing the Cougar CFV235 delivered fairly consistent thermal results across different configurations. With the default setup, the system recorded 53°C over ambient on the CPU and 49°C on the GPU. Taking off the mesh top panel produced similar behaviour, with the CPU reaching 53°C and the GPU 49°C. So the mesh isn’t too restrictive.

Removing the glass side panel had little effect on CPU or GPU thermals at 52°C and 48°C, respectively. But adding bottom intake fans reduced GPU temperature further to 46°C over ambient, while CPU temperature remained the same at 52°C. Overall, the results suggest the case’s stock airflow configuration is reasonably well balanced, but there are minor GPU thermal gains to be had from adding bottom intake airflow.

Noise Output

As with thermals, the noise testing shows only a minor difference between configurations under load. In the default configuration, the maximum load noise measures 52 dBA, which drops to 49 dBA when bottom intake fans are installed – showing the cooler GPU temperature helped reduce fan speed.

At idle, the system remained consistent across all configurations at around 36–37 dBA. Overall, our testing would suggest the additional bottom fans help reduce system noise slightly under load, while panel removal has a minor impact on acoustics.

Closing Thoughts

First impressions of the Cougar CFV235 are good thanks to its distinctive design. Cougar’s Central Floating Ventilation layout gives the chassis a unique look that stands out from more conventional mid-tower designs, while the overall construction feels surprisingly solid and well put together. Panel fitment is good, materials feel sturdy, and the case generally gives the impression of a well-built product.

Thermal performance is decent rather than class-leading. The stock configuration delivers stable temperatures in our testing, but it doesn’t quite extract the maximum possible cooling potential straight out of the box. That said, adding bottom intake fans provides a small but noticeable improvement in GPU temperature and noise, suggesting the airflow design benefits from a little extra intake to help feed the GPU and main chamber. Based on that, it does seem odd that Cougar doesn’t include bottom intake fans as the default.

There are a couple of minor usability issues worth mentioning, such as the lack of removable radiator brackets, meaning that it's difficult to connect cables at the top of the motherboard with an AIO installed. This is a feature I like to see at this price point. Additionally, the side cable cut-out grommet can be easily dislodged during cable routing, which may prove to be a little frustrating during the build process.

Even with those small drawbacks, the CFV235 still offers a well-rounded package with strong build quality, extensive hardware compatibility, including back-connect motherboards, big graphics cards, plenty of cooling potential, and a distinctive aesthetic that all work in its favour. Thermal performance is also perfectly respectable once airflow is optimised with bottom intake fans. For builders looking for something a little different visually without sacrificing practicality or build quality, the Cougar CFV235 is a solid option.

UK availability is scarce but we found it listed on Amazon HERE.

Pros: 

• Unique look with the free-floating top chamber.
• No adverse chassis flex due to the 1.5mm thick steel frame.
• Good hardware support, with up to EATX motherboards, including back connect, and big graphics cards.
• Included six-port PWM ARGB hub.

Cons:

• Thermal performance is a little limited out of the box.
• Non-removable top radiator bracket.
• Side cable grommet is easily dislodged.

KitGuru says: If you want a case that has a distinctive look but doesn't sacrifice build quality or practicality, the Cougar CFV235 is worth a look.

The post Cougar CFV235 Case Review first appeared on KitGuru.

Antec and Noctua have partnered on a new Noctua Edition of the Flux Pro chassis, combining Antec’s high‑airflow design with Noctua’s latest flagship fans.

The Flux Pro is known for its ventilation and layout, but the Noctua Edition pushes its noise‑to‑performance efficiency further. Antec says the upgraded model can reduce noise levels by up to 8dB(A) while keeping component temperatures broadly unchanged. That improvement comes from the new G2‑series fans, which run significantly quieter at equivalent airflow and are tuned to avoid harmonic vibrations by offsetting adjacent fan speeds.

For additional acoustic control, the case includes Noctua’s NA‑AV4 anti‑vibration mounts. The Noctua Edition also integrates the NA‑FH1 fan hub, allowing all pre‑installed fans to be controlled through a single motherboard header. The hub arrives pre‑installed with extension cables already routed, reducing setup time for builders.

Beyond cooling, the Flux Pro’s reputation for build quality and flexibility remains intact. Its internal layout supports both air and water-cooled configurations, with ample space for high‑end GPUs, radiators and cable management. The Noctua Edition adds subtle exterior changes too, including dark‑brown accents, brown silicone grommets and discreet Noctua logos across the panels.

The Antec Flux Pro Noctua Edition is available now priced at €399.90.

Discuss on our Facebook page, HERE.

KitGuru Says: We've seen Noctua Edition graphics cards in recent years and now we are moving on to Noctua Edition cases. Would you like to build a system inside one of these?

The post Antec and Noctua collaborate on Flux Pro Noctua Edition PC case first appeared on KitGuru.

Chieftec has introduced the BW‑01B‑OP, a new UNI Series ATX workstation chassis built for professional users who need high‑capacity storage and flexible cooling options. The design focuses on practicality and durability, wrapped in a clean, understated exterior with a modern hinged front door.

The case is constructed from 0.6mm SGCC steel and measures 510×200×465mm, offering support for Mini‑ITX, mATX, and ATX motherboards. Chieftec includes a pre‑installed 120mm PWM HDB fan at the rear, with additional cooling support for up to two 140mm front fans and up to three 140mm top fans. The top panel can also house 240mm or 360mm radiators when the upper 5.25in bay is unused, giving builders room for workstation‑class thermal setups.

Storage capacity is one of the BW‑01B‑OP’s defining features. The chassis provides two tool‑less 5.25in external bays, six 3.5in trays, and four 2.5in trays, all supported by an easy‑to‑remove cage system designed for creators and users managing large data libraries. Rubber‑grommeted cable routing holes help maintain clean internal layouts and unobstructed airflow.

Inside, the case supports CPU coolers up to 157mm tall and graphics cards up to 310mm—or up to 410mm when the 2.5in cage is removed. Seven expansion slots and ATX PSU support (up to 160mm) round out the internal layout.
Front I/O includes USB Type‑C, USB3.0, audio‑out, and mic‑in. Chieftec also supplies a removable bottom dust filter and a magnetic top filter, and the chassis carries a 24‑month warranty.

Discuss on our Facebook page, HERE.

KitGuru Says: Will you be considering a Chieftec chassis for your next build? 

The post Chieftec prioritises storage with its latest UNI chassis first appeared on KitGuru.